Blanket Warming Cabinet CE Model Operation, Maintenance and Installation Manual Issue 8 Oct 2011

Table of Contents Features... 3 Quality Policy... 3 Section A – Unit Operation ... 4 Section B – Unit Maintenance... 5 Trouble Shooting Guide ... 6 Wiring Diagram ... 7 Section C – Unit Installation ... 8 Unit Specifications ... 10 Malmet Warranty Statement... 11

Issue 8

Page 2

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual Features Malmet Blanket Warming Cabinets are designed to hold 9 to 12 blankets. Do not overload shelves. Heated air must be allowed to circulate around the blankets. The temperature can be adjusted up to a maximum of 60°C and has a lock out feature, which allows only authorised staff to change the temperature. NOTE:

This Blanket Warmer is specifically manufactured for BLANKETS ONLY. To avoid the risk of serious injury, do not place fluids of any description in this unit.

The unit can be left on permanently as power consumption is minimal. Electrical Rating

240V 50Hz 2.8 Amps supplied with IEC power cord standard 10 Amp plug.

Wall Recessed

Connect to standard 240V outlet and position in cavity assuring doors can open and shut in a corner manner. Plug shall be accessible after installation. Dimensions of space (e.g. at least 30mm around the appliance) are to be provided for the appliance.

Wall Mounted

NOTE:

Place into position and bolt to the wall using bracket supplied and plug unit into standard 240V outlet.

This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance.

Quality Policy Malmet (Australia) Pty Ltd is Quality Certified to ISO 9001 and guarantees the quality of this product. Should you have any problems with your machine, contact the company from whom you purchased it, or Malmet (Australia) Pty Ltd.

Malmet (Australia) Pty Ltd Head Office and Factory PO Box 373 LEETON NSW 2705 Telephone: Facsimile: E-mail: Web Site: Issue 8

(02) 6953 7677 (02) 6953 6266 [email protected] www.malmet.com.au

Page 3

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual

Section A – Unit Operation NOTE The Blanket Warming Cabinet is factory set to 60°C

Before starting the Unit The unit should be run initially on a power supply not protected by an earth leakage circuit breaker for approximately three hours. This will allow any moisture in the heaters to dry out. The unit can then be connected to an earth leakage circuit breaker protected circuit if required. Plug into standard 240V outlet.

Starting the Unit Power ON, the preset temperature of the cabinet appears for approximately five seconds. After five seconds the unit switches to display the actual cabinet temperature.

Changing the set temperature (lock out feature) AUTHORISED PERSONNEL ONLY Authorised operators can change the temperature by holding the up and down temperature buttons at the same time for a total of 5 seconds. The temperature can then be adjusted. The setting will revert back to tamper proof 5 seconds after the temperature is adjusted or if the up and down temperature buttons are not pressed within 5 seconds. The unit has a built in electronic over temperature cut out which will switch off the elements if the selected temperature is exceeded by 5°C, and ‘Ot’ w ill flash on the display panel. (See Fig 1) If the electronic cut out fails, a secondary safety bi-metallic cut out temperature switch will switch off the power to the elements and the controller.

Fig 1

Issue 8

Page 4

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual

Section B – Unit Maintenance Preventative Maintenance Daily

Wipe out inside doors and chamber with warm water and detergent.

Weekly

Wipe over outside panels with stainless steel cleaner.

Yearly

Check electrical connections. Note: Disconnect power before performing Yearly maintenance.

Units fitted with castors should have regular Test and Tag procedures undertaken.

Issue 8

Page 5

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual Trouble Shooting Guide Problem Display not on or wont turn on.

Probable Cause No Mains power supply.

Suggested Remedy

Power point not turned on.

Check power supply and lead plugged in.

Display will not turn on.

Check power switched on.

Faulty display board.

Press Standby button.

Interconnecting harness failure.

Switch off power supply at main and Call for Service.

Relay board fault.

Switch off power supply at main and Call for Service. Switch off power supply at main and Call for Service.

Display turns on. (Runs for approximately ½ - 1 hour then turns off).

Fan failure.

Switch off power supply at main and Call for Service.

Display is on but unit not heating.

Element failure.

Switch off power supply at main and Call for Service.

Relay board failure.

Switch off power supply at main and Call for Service. Display indicates Ot

Fan Failure. Element on. Continuously unable to switch off. (Relay Board Failure)

Switch off power supply at main and Call for Service. Switch off power supply at main and Call for Service.

Display indicates O/C

Control Temperature Thermistor is broken or unplugged.

Switch off power supply at main and Call for Service.

Display on but unit cooling down.

Element failure.

Switch off power supply at main and Call for Service.

Relay board failure.

Switch off power supply at main and Call for Service.

Issue 8

Page 6

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual Wiring Diagram

Drg: BWFW_4_E_2

Issue 8

Page 7

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual

Section C – Unit Installation Floor Bench Skirt The Factory will fasten the Floor-Bench Skirt when ordered with a cabinet. To level, remove the four plastic plugs from the inside floor and adjust the feet by turning the slotted screw head. When level replace the plugs. If the Floor-Bench Skirt is ordered separately to convert a cabinet the conversion will take approximately fifteen minutes and only require a screwdriver. Place the cabinet on its back, the base is pre-drilled with ten nutsert holes. Using the screws supplied fasten the Floor-Bench Skirt. Stand the unit upright and level as above. The front panel of the Floor-Bench Skirt is removable to clean under the unit.

Combination Cabinets The Factory will combine cabinets when ordered as a combination unit. To level, remove the four plastic plugs from the inside floor and adjust the feet by turning the slotted screw head. When level replace the plugs. The front panel of the floor skirt is removable to clean under the unit.

Cabinet Stand The Factory will fasten when ordered with a cabinet. To level, remove the front panel of the stand and adjust the feet by turning the slotted screw-head. This panel can also be removed to clean under the unit. If the stand is ordered separately to convert a cabinet the conversion will take approximately fifteen minutes and only require a screwdriver. Place the cabinet on its back, the base is pre-drilled with ten nutsert holes. Using the screws supplied fasten the stand. Place the unit upright and level as above.

Combination Conversion Kit This comprises a Floor-Bench Skirt and a Rear Joining Bracket. Conversion will take approximately fifteen minutes and only require a screwdriver. Place the bottom cabinet on its back. The base is pre-drilled with ten nutsert holes. Using the screws supplied fasten the FloorBench Skirt. Stand the unit upright. Remove the 7 plugs (3 small and 4 large) on the top of the bottom cabinet, place the top cabinet in position locating the bottom hinge bolts in the four large holes. Remove the two screws, in the cabinet that secure the slide out service tray and slide out as far as it will go. There are three securing holes located inside the top of the service compartment. Using the screws supplied fasten the cabinets together and replace the service tray.

Issue 8

Page 8

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual The back of both cabinets are pre-drilled with four nutsert holes, using the screws supplied, fix the Rear Joining Bracket into position. Place the cabinet in position and level. NB: Plugs must be replaced after levelling of the temperature control of the cabinet may be compromised.

Wall Mounted Cabinet All cabinets are supplied with a Wall-Mounting Bracket as standard. Secure the bracket to the wall ensuring it is level. We recommend 4 (8mm x 50mm) long coach screws for stud position walls and dyno bolts for solid walls. Two people are required to lift the cabinet to the height of the Mounting Bracket, move the top of the cabinet to the wall at approximately 45° and lo cate on the Wall Mounting Bracket. When secure swing the bottom of the cabinet to the wall ensuring it is firmly pushed onto the wall bracket. To remove, reverse this procedure. CAUTION: BLANKET CABINETS WHEN FULLY LOADED WEIGH APPROXIMATELY 120KGS

Issue 8

Page 9

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual Unit Specifications Capacity

Blankets

9 to 12 (recommended)

Volts

240V

Phase / Hz

1 ph / 50 Hz

Amps

2.8 Amps

Watts

0.6 kW

IEC right angle Power Cord with 3 Pin Plug

10 Amp (into standard GPO 240 Volt)

Circular Unfinned

Stainless steel sheathed 10mm diameter tubular

Rated

600 watt

Microprocessor Control Relay

PCB (SKCM325) Access via compatible RS232

Overtemp Protection

Electronic cutout @ 5°C above set point

Temperature Control

Incremental 1°C – 60°C

Factory set at 60°C

Secondary Overtemp Protection

High Limit

Auto reset Bi-Metallic Disc 80°C

Doors

Bi-parting, double glazed with powder coated frames

Cabinet

304/4 and 430D stainless steel

Electrical Rating

Electrical Connection

Elements

Control PCB

Materials

Note 1: If the supply cord is damaged it must be replaced by a special cord or assembly from the manufacturer.

Issue 8

Page 10

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual

Warranty Statement – Australia Only Subject to the following conditions we provide, from the date of purchase, the following warranty:

• •

Functional components found within the unit to be defective in workmanship or material will be replaced free of charge subject to the periods of warranty specified. The structural warranty covers any structural components within the unit, which fail to perform their intended function due to faulty manufacture or deterioration within the warranty period.

This

warranty

only

covers

products

manufactured

by

Malmet

(Australia)

Pty

Ltd.

Conditions and Exclusions

• •

• • • • • • • • •

Equipment must be installed according to our instructions (outlined in our Operation, Maintenance and Installation Manual) and operated to the purpose it was designed. Warranty shall not cover damage, malfunction or failure resulting from accident, misuse or misapplication, improper or unauthorised repair, neglect or modification or use of unauthorised replacement parts or accessories, or improper voltage. The warranty shall be void if the serial number is removed or altered. Parts damaged in transit back to Malmet Leeton due to poor packaging could result in warranty claim being rejected. Any part tampered with or has unauthorised repairs and modifications will be rejected as a warranty claim. Reasonable access must be allowed for maintenance. If any additional equipment is needed to provide access to the unit, this must be provided (and paid for) by the owner. It is the owner’s responsibility to provide safe access to the unit. Malmet, or any of its authorised service outlets, may refuse to do maintenance or warranty work if access is unsafe. Should a warranty claim be rejected you will be advised in writing with a full explanation of our reasons. It is our policy to have a Warranty Claim Procedure that is fair to our customers and provides an efficient system of replacement and/or repair of faulty parts. If at any time you believe we are not meeting our commitment to you please contact Malmet Head Office – Leeton. No responsibility will be accepted for outside elements such as storms, pest and vermin that may cause damage to the unit. No responsibility will be accepted for damage contributed by electrical surges or brown outs or any other consequential damages. If there is no certificate of compliance for plumbing or electrical, Malmet reserves the right to refuse service on non-compliant installations.

Issue 8

Page 11

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual •

A charge will be made for work done or service call where:

•

There is nothing wrong with the unit.

•

The defective operation of the unit is due to failure of electricity or water supply.

•

Defects are caused by neglect, incorrect application, abuse or by accidental damage of the unit.

• • • • • •

An unauthorised person has attempted to repair the unit.

Harsh environmental situations such as water quality that may cause the water tank damage can not be considered warranty. Claims for damage to contents, carpet, ceilings, foundations or any other consequential loss either direct or indirect resulting from, power spikes, incorrect operation, incorrect installation or faulty product are excluded. All warranties are NOT transferable. Unauthorised use of non-genuine Malmet Parts in units covered by Warranty will void all warranty and warranty claims. To the extent permitted by law Warranty labour (service work) shall not include units located outside of city metropolitan areas and costs outside these areas shall be borne by the Customer. The Customer shall be notified of this prior to the warranty call out.

Warranty on Replacement Parts Parts replaced under warranty are warranted for the balance of the original warranty period for that product.

Unit Components

Parts

Labour

Structural Guarantee

1

1

All other components

1

1

Date Sold: ...

Warranty Expiry Date: ...

Sold To:

Issue 8

For Service Contact:

Page 12

7th October 2011

Blanket Warming Cabinet CE Model

Operation, Maintenance and Installation Manual Proof of Purchase It is important that the name of the distributor from whom you purchased your product and the name of the installer are recorded at the front page of this manual. The installer is responsible for the correct installation, start up and demonstrating the operation of this product. They are also responsible for issuing the relevant certificates of compliance. (These may differ from state to state) Please attach your proof of purchase. Your receipt/invoice is your warranty and will be required to validate any warranty.

E.&O.E. In the interest of continued product improvement, Malmet (Australia) reserves the right to alter specifications without notice.

Issue 8

Page 13

7th October 2011

Manufactured by Malmet (Australia) ABN 95 001 717 791 www.malmet.com.au

P/N 8-M00-83-900