SHIN-NIPPON
XL-1 Led Slit Lamp Service Manual
Service Manual
5 Pages
![LED Slit Lamp XL-1 Service Manual This service manual is for Ajinomoto’s Service engineers and their distributor’s service person.](https://public.bioclinicalservices.com.au/library/representations/proxy/eyJfcmFpbHMiOnsiZGF0YSI6NjM4NCwicHVyIjoiYmxvYl9pZCJ9fQ==--894b991cf2baee38a3136d8fe3e0c86eff4733a6/eyJfcmFpbHMiOnsiZGF0YSI6eyJyZXNpemUiOiIzMjB4In0sInB1ciI6InZhcmlhdGlvbiJ9fQ==--4214356078d1f110e449cda512a9432562da3e70/xl-1_led_slit_lamp_service_manual.pdf.png)
Preview
Page 1
LED Slit Lamp
XL-1
Service Manual This service manual is for Ajinomoto’s Service engineers and their distributor’s service person.
1.
2.
Illumination Light is OFF (照明が点灯しない) ① The battery is too low. (バッテリーが低下している) →Re-charge the battery. (電池を充電する) ② Slit is closed. (スリットが閉じている) →Open the slit ring. (スリットを開く) ③ Illumination control volume is set to low position. (光量調節が低くなっている) →Set to high position to get more light power. (光量調節を高めに設定する) ④ Please contact to Sales representative if above action does not help. (上記内容で対応できない場合は、販売店に連絡してください。) Slit light is not at center position. ① Slit light is shifting to right or left. (スリット光が左右にずれている) →Normal if the shift level is within ±0.5mm. (ズレが 0.5mm 以内であれば問題ない) 1. Check the screw. Tighten the screw if it loosens. (ネジが締まっているか確認する) 2. In case illumination light is shifting to right or left. (照明光が左右にシフトしている場合) A) Turn the Illumination tube by observing the illumination light. You need to un-loosen the screw and rotate then tighten the screws when you adjusting the light position. (照明光を観測しながら照明チューブを 回転させる。最初ネジを緩めて、次に 回転させ、ネジを締める) B) Please take a next step if the above A) does not work well. (上記でうまくいかない場合は、次のよ うにする) Please see C). C )を参照する。
Need horizontal adjustment.
C) Horizontal adjustment. C-1 Remove battery (電池を取り外す)
3.
Objective cover replacement. 対物レンズカバーの交換 1. Unscrew the two screws and remove the cover and set new cover. ネジ2カ所を緩めてカバーを外して新 しいカバーを装着してください。 2. Please ask sales distributor if the objective lenses are damaged. You can not replace the objective lenses without special calibration instruments. 対物レンズが傷ついている場合は販売店に 連絡してください。校正機器が状態で交換 することはできません。
4.
Observation image is not clear (観察像が鮮明でない). z Remove the dust 埃を取り除く z Clean up the lenses. レンズをきれいにする。 Please see instruction manual for daily maintenance. 説明書の日常点検を参照してください。
5.
Illumination Sliding is heavy (照明のスライドが重い) Please add some silicon oil or grease. Grease lightly to inside of sliding position. Do not grease too much on the top of the sliding place.
EU Representative
FAUSTO GUZZETTI (SHIN-NIPPON TECHNICAL CENTER) VIA SOLFERINO,5 21057 OLGIATE OLONA(VA), Italy Supplied by
East Wing 7F, TFT Building, 3-1-22 Ariake, Koto-Ku, Tokyo 135-8071, JAPAN TEL:813-3528-4416 FAX: 813-3528-4426 http://www.shin-nippon.jp http://www.ajitrade.com Manufactured by
Ohira Co., Ltd 258 Nishi Izumida, Minami-Uonuma, Niigata 949-6615, JAPAN Approval: 15B2X00003